Salisbury Linemen’s Sleeves – Molded Type II Class 2
$295.00 – $420.00
Salisbury Rubber Insulating Sleeves for Lineman provide personal protection against this accidental brush contact with energized lines and equipment.
Please view sizing chart and colors under Additional Information.
CALL FOR PRICING AND AVAILABILITY
Description
Salisbury Rubber Insulating Sleeves for Lineman
Salisbury Rubber Insulating Sleeves extend coverage of the arm from the cuff of rubber insulating gloves to the shoulder, fully protecting these areas from accidental contact with energized conductors and equipment. Salisbury rubber sleeves feature a reinforcing fold at the cuff. This fold is preferred over a rolled bead because it adds less bulk to the cuff and fits into the glove easier without pushing. Two different processes are used to manufacture insulating sleeves; dipping and molding. Both meet the current requirements of ASTM D1051 -08 and offer the same high level of quality and protection.
Salisbury Rubber Insulating Sleeves Sizing
Salisbury Sleeves should be selected to fit the arm comfortably, covering from the top of the shoulder to inside the top of the glove. Regular size sleeves are the shortest and have the smallest arm and wrist openings. To minimize the possibility of the sleeves pushing gloves off the hand, size the sleeve to the shortest length possible while maintaining complete coverage to the shoulder.
Salisbury Molded sleeves are manufactured by either injection or compression molding methods. The advantage these methods offer is the ability to produce sleeves of Type I or SALCOR® Type II synthetic rubber. SALCOR® sleeves provide the same high quality and electrical protection as natural rubber, with the added benefit of being resistant to ozone and ultraviolet radiation. Type I sleeves are available in black, yellow or maroon. Type II SALCOR® sleeves are black or orange. Molded sleeves are available in curved arm style only.
Note: While these instructions do not serve as a warning against all potential hazards, they should be followed in addition to your employer’s safe work practices and procedures.
Care and use of insulating gloves and sleeves
Rubber insulating gloves and sleeves, when in good condition, and properly used, are designed to protect the wearer from serious injury, death, and the potential danger of electrical shock and burn. Both the inside and outside of gloves and sleeves should be inspected visually at least once a day. Do not use gloves or sleeves that show any signs of damage or deterioration such as swelling, softness, hardening, stickiness, ozone deterioration, or sun-checking. Many chemicals, especially petroleum-based products, such as oils, gasoline, hydraulic fluid, inhibitors, hand creams, pastes and salves, can damage gloves and sleeves. If contact is made with such products, wipe off contaminants immediately.
Do not wear rings, watches, jewelry, or sharp objects under rubber gloves or sleeves. Clean with mild soap, then rinse with clear water and air dry. Store in a protective bag or roll-up.
Rubber Sleeve Sizing
Rubber Sleeves should be selected to fit the arm comfortably, covering from the top of the shoulder to inside the top of the glove. Regular size sleeves are the shortest and have the smallest arm and wrist openings. To minimize the possibility of the sleeves pushing gloves off the hand, size the sleeve to the shortest length possible while maintaining complete coverage to the shoulder.
Salisbury offers both molded and dipped sleeves
Molded sleeves are manufactured by either injection or compression molding methods. The advantage these methods offer is the ability to produce sleeves of Type I or SALCOR® Type II synthetic rubber. SALCOR sleeves provide the same high quality and electrical protection as natural rubber, with the added benefit of being resistant to ozone and ultraviolet radiation. Type I sleeves are available in black, yellow or maroon. Type II SALCOR sleeves are black or orange. Molded sleeves are available in curved arm style only.
Dipped sleeves are manufactured in the same way as Salisbury rubber insulating gloves. Porcelain forms are dipped into liquefied rubber, dried, trimmed, marked and cured. Every sleeve receives the same quality inspections and electrical testing before shipping. Dipped sleeves are available in the same colors as dipped gloves, including two color combinations.
Salisbury is the only manufacturer that offers two popular styles of dipped lineman’s sleeves: straight and extra curved. Both styles are available in every color or color combination, size, and voltage class. Most importantly, all are made to the same rigid levels of quality demanded by Salisbury.
Additional information
Weight | 6 lbs |
---|---|
Choose Color | |
Choose Size | |
Accessories | 15" Straps w/ 4 B2 Buttons, 4 Screw Type Buttons, Harness w/ 4 B2 Buttons, One Piece Sleeve Button, Sleeve Bag Canvas, 28" x 9" Top to 7", Sleeve Bag Canvas, 30" x 9" x 2-1/2" |
Usually Ships | |
Manufacturer Warranty | |
Specification | <table cellspacing="0" width="100%"> </table> |
Manufacturer |
Only logged in customers who have purchased this product may leave a review.
-
$118.00 – $219.00
Reviews
There are no reviews yet.